Distribution Partnerships
Become a Level Finish Distribution Partner
Partner with a manufacturer dedicated to helping distributors grow through premium products, reliable inventory, and technical support.
Premium positioning
Reliable U.S. manufacturing
Private label programs
Alpha P400 vs 3M Cubitron II: Test Results | Level Finish
Level Finish · Technical Test Report
Alpha P400 vs 3M Cubitron II: the thorough comparison
Level Finish Alpha P400 disc vs 3M Cubitron II P400 disc, both 150 mm (6 in) hook-and-loop. This is the thorough P400 comparison: a controlled 60-second standard test at 126 measured coordinates per product, a 160-second endurance phase, a post-endurance finish check, and before-and-after microscopy of both discs. The headline is the honest one: 3M led the 60-second cut, and Alpha led the finish. Every figure below is a recorded test mean or a recorded measurement from the test report, published with the results that favor 3M stated as plainly as the results that favor Alpha. The figures are the recorded test means. They are not rounded to a commercial or marketing value.
What happened, in short
- Standard test, 60 seconds: 3M recorded the higher mean material removal, 1.043 vs 0.986 for Alpha, about 5.8% higher. Removal and depth figures in this report carry no unit in the source data, so none is stated here.
- Standard test finish: Alpha recorded the lower mean Ra, 0.614 µm vs 0.774 µm for 3M, 20.7% lower, with substantially lower Ra variability (SD 0.058 vs 0.123 µm).
- Endurance, 160 seconds: 3M retained the higher mean removal, 1.392 vs 1.250 for Alpha, 10.2% lower for Alpha. Both abrasives were still cutting at 160 seconds. Alpha reached the coating floor at fewer coordinates, 6 of 27 vs 12 of 27 for 3M.
- Post-endurance finish: measured on fresh primer after endurance, Alpha recorded 0.446 µm mean Ra vs 0.549 µm for 3M, 18.8% lower.
- Microscopy: before-and-after images at 500x to 1200x. The report's observation: Alpha showed more intact pyramidal grains and tighter grain spacing at every magnification. The microscopy is qualitative; no grain count or grain size was measured.
Method and context
The objective was to compare the performance of 3M Cubitron II P400 and Level Finish Alpha P400 after 60 seconds of controlled sanding. The test articles were 150 mm (6 in) hook-and-loop discs, run on a 5 in, 3.0 mm orbit, 8-hole DA sander. The surface was a flat steel panel coated with 2K urethane primer at a coating thickness of 8.0 mils (203 µm). Each product was assigned its own test area: columns A to C for 3M and columns D to F for Alpha, rows 1 to 9, giving 126 coordinates per product in 2 x 2 inch squares. Baseline measurements were taken at all 126 locations per product, each product sanded for 60 seconds (T0 to T60), all 126 locations were measured again, and surface roughness (Ra) was measured at 12 locations per product.
The conditions were locked so that one variable only changed: the abrasive. Same operator. Same machine, same orbit, same speed. Same 8-hole pattern. Same pressure, 3 to 4 lbs. Same 60-second duration. Same test area per abrasive. One disc per product, with no second disc, no lane crossing, no added dwell, no overlap, no added weight, no air blasting, no additional pass, no added technique, no disc change, and no re-orientation.
Results: standard test material removal, 60 seconds
| Measure | 3M Cubitron II P400 | Level Finish Alpha P400 |
|---|---|---|
| Locations measured | 126 | 126 |
| Mean removal | 1.043 | 0.986 |
| Median removal | 1.100 | 1.000 |
| Removal SD | 0.299 | 0.273 |
| Removal CV | 28.69% | 27.66% |
| Positive removal | 126 of 126 | 126 of 126 |
3M produced approximately 5.8% greater mean material removal than Alpha during the controlled 60-second standard test. Alpha remained close in cutting performance and showed slightly lower removal variability. Two recorded values carry locked corrections from the test record: coordinate E9, originally 0.800, corrected to 1.00, and coordinate L1, originally 1.60, corrected to 1.30. The removal figures are reported exactly as recorded; the source data states no unit for them.
Results: standard test surface finish, Ra
| Measure | 3M Cubitron II P400 | Level Finish Alpha P400 |
|---|---|---|
| Mean Ra | 0.774 µm | 0.614 µm |
| Ra SD | 0.123 µm | 0.058 µm |
| Surface finish result | Coarser | Finer |
| Finish consistency | Higher spread | Lower spread |
Alpha gave up approximately 5.5% in mean material removal relative to 3M while producing approximately 20.7% lower mean Ra. Under the controlled standard-test conditions, 3M demonstrated the initial cutting-rate advantage, while Alpha demonstrated the stronger measured cut-to-finish balance.

3M P400 standard T60 Ra evidence. Mean Ra 0.774 µm, SD 0.123 µm.

Level Finish Alpha P400 standard T60 Ra evidence. Mean Ra 0.614 µm, SD 0.058 µm.
The cut-to-finish rules
There is no cut-and-polish trick in this test. The cut-to-finish comparison is only valid if the test does not separate the cut from the finish. Rule 1: total time, the total time is the only time allowed. Rule 2: total passes, the total passes are the only passes allowed. Rule 3: no additional technique is allowed. Rule 4: no additional pass is allowed. Rule 5: total cut equals total time; there is no second operation. Once the abrasive has completed its cut, the finish is the finish.
Results: endurance, 160 seconds

3M endurance baseline: A to C by rows 1 to 9, 27 coordinates.

Alpha endurance baseline: D to F by rows 1 to 9, 27 coordinates.
Each abrasive then completed four consecutive 40-second runs on a 27-coordinate grid (columns A to C for 3M, D to F for Alpha, rows 1 to 9), reaching 40, 80, 120, and 160 seconds of cumulative use. A blank final-depth entry is recorded as zero only where the coating was depleted to the material bottom or metal substrate; that zero is a confirmed floor condition, not missing data. At 120 seconds both abrasives remained visibly intact in the photographed condition. At 160 seconds both endurance lanes showed substantial coating depletion and visible substrate exposure in portions of the worked areas.
| Measure | 3M Cubitron II P400 | Level Finish Alpha P400 |
|---|---|---|
| T0 locations | 27 | 27 |
| T0 mean depth | 2.797 | 2.778 |
| Aggregate T0 depth | 75.51 | 75.01 |
| T160 mean depth | 1.405 | 1.529 |
| Mean removal | 1.392 | 1.250 |
| Removal SD | 0.29 | 0.27 |
| Removal CV | 20.9% | 21.8% |
| Floor coordinates | 12 of 27 | 6 of 27 |
At T160, 3M removed 1.392 while Alpha removed 1.250, a difference of 0.142, or 10.2% less removal for Alpha. Both abrasives continued to cut after 160 seconds. 3M retained the higher mean removal; Alpha retained the lower floor count, 6 of 27 versus 12 of 27. Two single-coordinate records from the grids: 3M coordinate C3 finished at 2.04 from an original T0 of 2.61, a removal of 0.57; Alpha coordinate E5 finished at 7.02 from an original T0 of 9.20, a removal of 2.18. These are individual coordinates, not averages.

3M P400 abrasive and panel condition at T40.

Level Finish Alpha P400 abrasive and panel condition at T40.

3M P400 abrasive and panel progression at T80.

Level Finish Alpha P400 abrasive and panel progression at T80.

3M P400 panel and disc condition at T120.

Level Finish Alpha P400 panel and disc condition at T120.

3M P400 panel and disc condition at T160.

Level Finish Alpha P400 panel and disc condition at T160.

3M P400 final T160 endurance-depth grid. Blank endpoint cells are entered as zero where primer was depleted to the material bottom or metal substrate. Twelve of 27 coordinates reached the floor condition.

Level Finish Alpha P400 final T160 endurance-depth grid. Blank endpoint cells are entered as zero where primer was depleted to the metal substrate. Six of 27 coordinates reached the floor condition. Confirmed E5 endpoint = 7.02.
Results: post-endurance surface finish, Ra
After endurance, surface finish was checked on fresh primer. These measurements were not taken on the endurance lanes; they are a post-endurance finish check, not a T160 lane measurement.
| Measure | 3M Cubitron II P400 | Level Finish Alpha P400 |
|---|---|---|
| Locations | 6 | 7 |
| Mean Ra | 0.549 µm | 0.446 µm |
| Ra SD | 0.035 µm | 0.046 µm |
| Ra CV | 6.4% | 10.3% |
Alpha measured 0.103 µm lower mean Ra than 3M after endurance. Against the standard-test means, mean Ra fell by approximately 29.0% for 3M and approximately 27.4% for Alpha. Both abrasives produced a finer finish after endurance than in the standard 60-second test, and Alpha produced the finer post-endurance finish.
Before-and-after microscopy
Each product was photographed under the same microscope before testing and again at the end of the complete trial, at 500x, 750x, 1000x, and 1200x magnification. In each pair, the original unused abrasive is on the left and the used abrasive is on the right. The report's observation: Alpha showed more intact pyramidal grains and tighter grain spacing at every magnification, and its grains were more regularly distributed, with less fracture than 3M. The report's own cautions apply: image sharpness, lighting, and contrast may affect the apparent differences, visible changes are observations rather than quantitative measures of wear or performance, and microscopy does not independently measure the worked panel's Ra, scratch depth, cutting rate, material removal, or absolute abrasive life. No grain-count or grain-size measurement was performed.

3M Cubitron II P400 abrasive microscopy at 500x. Left: original unused abrasive before testing. Right: used abrasive at the end of the complete trial.

Level Finish Alpha P400 abrasive microscopy at 500x. Left: original unused abrasive before testing. Right: used abrasive at the end of the complete trial.

3M Cubitron II P400 abrasive microscopy at 1200x. Left: original unused abrasive before testing. Right: used abrasive at the end of the complete trial.

Level Finish Alpha P400 abrasive microscopy at 1200x. Left: original unused abrasive before testing. Right: used abrasive at the end of the complete trial.
Conclusions
3M won the initial cutting rate, with 5.8% greater mean removal in the standard 60-second test, and retained the higher mean removal after 160 seconds of endurance. Alpha won the surface finish, with 20.7% lower mean Ra and lower Ra variability in the standard test, and retained a finer finish after endurance, 0.446 µm versus 0.549 µm. Both abrasives remained functional after 160 seconds of cumulative use. That is the whole result, published so you can decide for yourself.
More test results
Alpha P600 vs 3M Cubitron II 737U: see the P600 test results. Alpha P800 vs 3M Cubitron II 737U: see the P800 test results. Alpha P180 vs 3M Cubitron II, two controlled tests: see the P180 test results. Alpha P80 vs 3M Cubitron II, two controlled tests: see the P80 test results. Omega P2000 vs 3M Purple P2000, filmed: see the filmed test results. More reports are filed here as testing is completed.
Notes and limitations
1. The standard test used one disc per product and one 60-second run per product. 2. The endurance test used one disc per product and four 40-second runs per product. 3. The endurance Ra measurement was a post-endurance check on fresh primer, not a measurement on the endurance lanes. 4. The microscopy images are qualitative; no grain-count or grain-size measurement was performed. 5. The test was conducted on flat steel panels with 2K urethane primer; results may differ on other substrates, coatings, or shapes. 6. The test was conducted by a single operator; operator technique may affect the results. 7. The results are specific to P400 grit; other grits may behave differently.
Removal and depth figures are reported exactly as recorded in the test report, which states no unit for them. Ra figures are in micrometres (µm) as recorded. Source: P400 Thorough Comparison Test, Level Finish technical comparative test report.