Distribution Partnerships

Become a Level Finish Distribution Partner

Partner with a manufacturer dedicated to helping distributors grow through premium products, reliable inventory, and technical support.

Premium positioning

Reliable U.S. manufacturing

Private label programs

Alpha Cutting Compound vs 3D ACA 510 Premium: Filmed Cutting Test | Level Finish

Level Finish · Technical Test Report

Alpha Cutting Compound vs 3D ACA 510: full correction in 1:16 against 2:00

Level Finish Alpha Cutting Compound vs 3D ACA 510 Premium. Two cutting compounds, one scratch field, one rotary at 1,200 RPM. Each compound corrected a matching section of Omega P1500 scratches on a high-solids clear coat, each run continued until the P1500 scratches were fully removed, and the full runs were filmed. This report is the filmed record: the times, the material each correction needed, and the condition of the evidence after each run.

Level Finish Alpha Cutting Compound bottle
Level Finish Alpha Cutting Compound.
3D ACA 510 Premium Rubbing Compound bottle, 32 oz
3D ACA 510 Premium Rubbing Compound, the 32 oz bottle used in this test.

How the test was run

  • One black panel in a high-solids clear coat, divided into sections by a tape line.
  • The scratch field for the whole trial was made with an Omega P1500 disc, sanded evenly left to right and right to left so the scratch pattern was consistent across the surface.
  • Each compound was dosed onto its own Level Finish X-tra Cut Wool Pad (XCW), 7.5 inch, and worked with the same FLEX rotary polisher at 1,200 RPM. Each pad started with four pea-sized dots of its compound.
  • Each wool pad was used only with its stated product. No other chemicals were used on the pads.
  • Each run continued until all of the P1500 scratches were removed from its section. Cutting time is counted from the moment polishing starts to the moment polishing ends. Both cutting runs were filmed at 4x speed, and the times below are the real times.
  • For each side, the filmed record holds the cutting run, the condition of the wool pad after the run, and the surface after wipe-down under an inspection light.
Level Finish X-tra Cut Wool Pad (XCW), side view
The pad used for both runs: Level Finish X-tra Cut Wool Pad (XCW), 7.5 inch, side view.
Level Finish X-tra Cut Wool Pad (XCW), top view
The XCW pad from above. Each compound had its own new pad, used with that compound only.

Cutting time

  • 3D ACA 510 Premium: 2:00
  • Level Finish Alpha Cutting Compound: 1:16
  • On these matched sections, Alpha finished its correction 44 seconds sooner.
  • Partway through its run, the ACA 510 side needed additional compound applied to finish the correction. That stop and re-application are visible in its film. The Alpha side finished on the four dots it started with, and no scratch removal remained when its run ended.
Bar chart of cutting time: 3D ACA 510 at 2:00, Alpha Cutting Compound at 1:16
Cutting time to full removal of the P1500 scratch field, same panel and protocol for both compounds.
Frame from the filmed ACA 510 cutting run
A frame from the ACA 510 cutting film, mid-run.
Frame from the filmed Alpha cutting run
A frame from the Alpha cutting film, mid-run.

The wool pads after the runs

After the ACA 510 run, the wool pad face was clean and white, fibers fully lofted, with no visible residue. That run had worked through its starting dose and the additional compound applied partway through.

After the Alpha run, the wool pad carried the compound's blue tint through its fibers, with the pile lying flatter and residue worked into it. That residue is compound left over from the starting dose: the correction was complete before the pad's material was spent.

Pad condition is reported here as a photographic record, with the runs' material use stated alongside it.

The XCW wool pad after the ACA 510 run
The ACA 510 pad after its run: clean, white, and fully lofted.
The XCW wool pad after the Alpha run
The Alpha pad after its run: blue compound tint through the fibers, pile lying flatter, material left over from the starting dose.

Wipe-down and the surfaces

The Alpha residue wiped off with a microfiber in a few passes, which is part of the filmed record for that side. The ACA 510 side's surface film also includes a wipe during its inspection pass.

On both sections, the matte P1500 scratch field was replaced by a glossy surface carrying the fine rotary swirl trails a cutting step leaves. Refining those trails is the job of a finishing polish, which is a separate step and is not part of this test.

The ACA 510 section under the inspection light after correction
The ACA 510 section under the inspection light after correction.
The Alpha section under the inspection light after wipe-down
The Alpha section under the inspection light after wipe-down.

What this report does not claim

  • No gloss, Ra, or removal measurements were taken. This is a filmed-evidence comparison, and every figure in it is a time or a count from the film.
  • One panel, one operator, one section per compound. The times belong to this protocol and are not a promise for every panel, pad, or machine.
  • 3D ACA 510 Premium is a respected cutting compound with a stated purpose of cutting P1000 or finer scratches on hard clear coats. It corrected its section fully in this test. The differences recorded here are the time the correction took, the material the correction needed, and the condition of the evidence after each run.

Related filmed test: Omega P2000 vs 3M Purple P2000, filmed test results.