Distribution Partnerships

Become a Level Finish Distribution Partner

Partner with a manufacturer dedicated to helping distributors grow through premium products, reliable inventory, and technical support.

Premium positioning

Reliable U.S. manufacturing

Private label programs

Omega P600 vs Kovax Sky K-600: Test Results | Level Finish

Level Finish · Technical Test Report

Omega P600 vs Kovax K-600: comparable cut, finer measured finish

Level Finish Omega P600 refining disc vs Kovax / Eagle Super Assilex Sky K-600. One controlled comparison on a clear-coated test panel, run under a defined 40-pass sanding cycle, with 24 stock-removal locations measured per product. Under that cycle, the two discs cut essentially the same amount of material. The difference was the surface left behind: Omega recorded the lower average roughness, and the finer reading at every matched location. Both results are published here, because at P600 the cut and the finish are two separate questions, and the honest answer is different for each one.

The shared clear-coated test panel with the four test sheets in their zones: Kovax Lemon K-800, Omega P600, Kovax Sky K-600, and Omega P800
The shared test panel after the tests, with each product’s sheet in its zone. From the left: Kovax Lemon K-800, Omega P600, Kovax Sky K-600, and Omega P800. All four products were tested on this one panel.

Omega P600 results graphic: mean Ra Omega 0.3344 µm vs Kovax Sky K-600 0.3750 µm

The Omega P600 post graphic, as published on our Facebook and Instagram. Mean post-sanding Ra: Omega 0.3344 µm vs Sky K-600 0.3750 µm.

What happened, in short

  • Material removal: essentially comparable. Mean removal was 0.1763 for Omega vs 0.1738 for Sky K-600, a difference of 0.0025, approximately 1.44%. That is not a cutting victory, and this page does not present it as one.
  • Surface finish: Omega recorded the finer finish. Mean post-sanding Ra was 0.3344 µm for Omega vs 0.3750 µm for Sky K-600, approximately 10.83% lower.
  • Consistency at matched locations: Omega recorded the lower Ra at 5 of 5 matched sampling locations.
  • The honest summary: comparable cut, finer measured finish. The finish is the story of this test, not the removal.

Method

Both products were tested by dry hand sanding on a clear-coated panel, by the same operator, at 40 passes per product, using a soft interface to help manage pressure. Omega was tested in area D1:F8 and Sky K-600 in area G1:I8, on a grid of 2 by 2 inch squares, 6 by 16 inches per product, with stock removal measured at 24 locations per product. The two product systems are built differently: Omega is hook-and-loop backed and the Sky sheet is felt and loop backed, and each product ran with the interface arrangement appropriate to it, so the physical systems were not identical. Calculated removal is the post-sanding reading minus the baseline reading at each matched location, and all negative calculated removal values were treated as zero for both products, under the locked rule in the verified record. Post-sanding surface roughness was recorded as Ra (arithmetic average surface roughness, in µm; lower is finer), sampled at rows 1, 2, 4, 5, and 7.

Results: material removal

Material removal Kovax / Eagle Sky K-600 Level Finish Omega P600
Mean removal 0.1738 0.1763
Median removal 0.190 0.175
Maximum removal 0.270 0.290
Sample standard deviation 0.0741 0.0664
Sum of 24 readings 4.17 4.23

The average difference was 0.0025 in Omega's favor, approximately 1.44%. The verified record is explicit on this point: do not turn that difference into a dramatic cutting claim. The removal in this test was essentially comparable.

Results: surface finish

Post-sanding Ra Kovax / Eagle Sky K-600 Level Finish Omega P600
Mean Ra 0.3750 µm 0.3344 µm
Absolute difference 0.0406 µm lower
Relative difference 10.83% lower
Matched locations where Ra was lower 0 of 5 5 of 5
Sample row Omega P600 Ra Sky K-600 Ra Difference
1 0.352 µm 0.408 µm 0.056 µm
2 0.339 µm 0.388 µm 0.049 µm
4 0.316 µm 0.350 µm 0.034 µm
5 0.324 µm 0.364 µm 0.040 µm
7 0.341 µm 0.365 µm 0.024 µm

Bar chart: mean post-sanding Ra, Omega P600 0.3344 µm vs Kovax Sky K-600 0.3750 µm

Omega's mean Ra was 0.0406 µm lower, approximately 10.83% lower, and Omega was finer at all 5 matched sampling locations. That is the measured finish advantage in this test.

Microscopy

Post-test microscopy documented substantial visible surface alteration for both abrasives compared with their own unused condition. No obvious catastrophic surface disruption was observed in the supplied fields. On the sanded clear coat, both products produced predominantly directional scratch patterns, isolated prominent lines occurred in both image sets, and the supplied fields do not establish broad gouging across either complete test area. The two abrasives also began from visibly different microscopic baselines: the unused Omega surface appeared fine and comparatively subdued, while the unused Sky surface appeared strongly textured. Because of that, the size of the visual change after testing is not a direct measure of comparative wear. Microscopy supports describing changes in visible surface condition. It does not independently quantify abrasive wear percentage, mineral loss percentage, loading composition, or remaining abrasive life, so none of those figures appear on this page.

An unused Kovax Sky K-600 sheet before the test
An unused Kovax Sky K-600 sheet. The report’s microscopy notes describe the unused Sky baseline as strongly textured.
A Kovax Sky K-600 sheet after the 40-pass test, carrying sanding residue
A Kovax Sky K-600 sheet after its 40-pass test on the panel, carrying the sanding residue.

How to read this test

P600 is a refining step on clear coat, and the surface it leaves is what the next grits inherit. In this test the two discs removed essentially the same amount of material, so the practical difference is the finish: Omega left the finer measured surface at every matched location. Which matters more depends on the job, and that call belongs to the technician. Our job is to publish the measurements exactly as recorded and let you decide for yourself. Note that this is the Omega P600 comparison against Kovax / Eagle Sky K-600. It is a different test from the Alpha P600 comparison against 3M Cubitron II, which has its own page.

More test results

Omega P800 vs Kovax Lemon K-800, the finer-grade companion test on the same panel: see the Omega P800 test results. Omega P2000 vs 3M Purple P2000, filmed side by side on one panel: see the filmed test results. Alpha P600 vs 3M Cubitron II, the test behind the Level Up headline: see the Alpha P600 test results. More reports are filed here as testing is completed.

Notes and limitations

Each comparison is a single controlled trial under its documented conditions, and the results describe that trial. Starting gloss was not identical across all areas of the test panel, which carried both P2000-sanded and compounded, refined areas. Negative calculated removal values were treated as zero for both products, under the locked rule in the verified record. Ra is the measured arithmetic average surface roughness under the documented test conditions; it is not a measurement of individual scratch width or depth. Results from one grit or substrate do not transfer to another.

Frequently asked questions

Did Omega P600 cut more than the Kovax K-600?

Essentially no. Mean removal was 0.1763 for Omega vs 0.1738 for Sky K-600, a difference of approximately 1.44%. The verified record describes that as essentially comparable, not a cutting victory.

What did Omega win in this test?

The finish. Mean post-sanding Ra was 0.3344 µm for Omega vs 0.3750 µm for Sky K-600, approximately 10.83% lower, and Omega was finer at 5 of 5 matched locations.

Is this the same test as the Alpha P600 page?

No. This page is Omega P600 vs Kovax / Eagle Sky K-600. The Alpha P600 page is Alpha vs 3M Cubitron II, a different product and a different opponent, with its own results.

Level Finish · St. George, Utah · level-finish.com · Source: Level Finish verified comparative test record and the full P600 vs K-600 test report supplied November 14, 2026. All numbers transcribed exactly from those records; no values added or altered.